Metal sulfur — FTIR absorption peaks and assignments
These are the characteristic FTIR wavenumbers where Metal sulfur tends to absorb, compiled from published literature and ranked by supporting evidence. Each assignment is traceable to a source (DOI) and cross-validated against our 130,000+ reference spectra and knowledge graph.
Backed by 8 cited sources
Hurtigt svar
Metal sulfur is usually assigned by looking for a recurring cluster of characteristic peaks rather than one exact textbook number. The table below shows where the literature most often places this group in FTIR, ranked by accumulated evidence.
Characteristic FTIR peaks for Metal sulfur
Mulige materialer
Spektrumlogik
En funktionel gruppetildeling bliver mere pålidelig, når flere forventede bånd optræder sammen. Brug denne side til at finde de stærkest understøttede toppe, og bekræft derefter, at den samme prøve udviser et sammenhængende mønster snarere end et enkelt isoleret hit.
Anvendelse i virkeligheden
Disse sider er nyttige til analyse af ukendte materialer, topforklaring i rapporter, polymerfejlfinding og verifikation af, om en kandidatmaterialefamilie er kemisk plausibel.
Almindelige fejl
- Brug af én funktionel-gruppe-side som en komplet materialebedømmelse uden at kontrollere resten af spektret.
- Antager, at det stærkeste bånd altid er det mest diagnostiske.
- At glemme, at forarbejdning, tilsætningsstoffer, ældning og blandinger kan flytte eller udvide forventede toppe.
Verifikationsrådgivning
Brug DSC, GC-MS eller TGA, når flere materialefamilier deler lignende bånd, eller når blandings-effekter gør FTIR-tildelingen usikker.
Litteratur bag disse tildelinger
-
600 cm⁻¹ tillid 1,0
“LLM confirmed rule peak-group candidate”
Aziz 等 - 2023 - Water remediation capability of cubic-phase CdS na DOI: 10.15251/DJNB.2023.181.203 -
1000 cm⁻¹ tillid 1,0
“The Fourier Transform Infra Red (FTIR) peak at (cid:2)482 (cid:2)2.56 PACS: appeared due to the simultaneous presence of absorption peaks for CdTe stretching mode as well as Cd-S 78.66.Sq cm(cid:3)1 cm(cid:3)1 Appearance of the broad peak b”
Utilization of residual CdCl2 in CBD-CdS to realize grain growth in CdTe: A novel route DOI: 10.1016/j.materresbull.2013.08.006 -
405 cm⁻¹ tillid 1,0
“LLM confirmed rule peak-group candidate”
60MeV Ni ion induced modifications in nano-CdS/polystyrene composite films DOI: 10.1016/j.radphyschem.2013.06.022 -
670 cm⁻¹ tillid 1,0
“LLM confirmed rule peak-group candidate”
Probing How Various Metal Ions Interact with the Surface of QDs: Implication of the Interaction Event on the Photophysics of QDs DOI: 10.1021/acs.langmuir.1c00548 -
1647 cm⁻¹ tillid 1,0
“A relatively strong and broad FTIR peaks at 1647 and 670 were observed due to the Cd-S bending and stretching vibration in the surfactant mediated films.”
Effect of Triton X-100 surfactant on thiol-amine cosolvents assisted facile synthesized CdS thin films on glass substrate by spin coating method DOI: 10.1007/s42452-020-2423-y -
453 cm⁻¹ tillid 1,0
“An additional cm(cid:1)1 Mo-S appears at 1116.4 and the characteristics peaks of cm(cid:1)1, peak is observed at 453.35 which corresponds to the cm(cid:1)1 cm(cid:1)1.”
Verma 等 - 2021 - The functionalization of polyacrylamide with MoS2 DOI: 10.1039/d0se01877e -
405 cm⁻¹ tillid 1,0
“And peak of the Cd-S bond at 405 was observed, which further testified the generation of CdS nanoparticles.”
Wang 等 - 2007 - Synthesis and characterization of CdSPVA nanocomp DOI: 10.1016/j.apsusc.2007.04.020 -
1389 cm⁻¹ tillid 1,0
“For MoS 2, the vibration cm-1 cm-1 mode at 1389 is assigned to Mo-S vibration, while the vibration mode at 1550 may be S-O asymmetric”
Hydrothermal synthesis of novel 1-aminoperylene diimide/TiO2/MoS2 composite with enhanced photocatalytic activity DOI: 10.1038/s41598-020-78894-y
See Metal sulfur in your own spectrum
Upload dit FTIR-spektrum og få en fuld tolkningsrapport — peak-tildelinger med litteraturhenvisninger, biblioteksmatch og en tillidsvurderet beviskæde — på få sekunder.