What absorbs at 1768 cm⁻¹ in an FTIR spectrum?
A band near 1768 cm⁻¹ can point to several functional groups. Below are the most likely assignments, ranked by how much published evidence supports each — every one traceable to literature (DOI) and cross-validated against our 130,000+ reference spectra and knowledge graph.
Backed by 3 cited sources
Schnelle Antwort
A band near 1768 cm⁻¹ is usually interpreted by checking which functional groups repeatedly co-occur there in the literature, then confirming at least one or two additional peaks in the same sample. This page ranks those assignments by accumulated evidence rather than by a single fixed textbook rule.
Mögliche Funktionsgruppenzuweisungen
| Funktionelle Gruppe | Unterstützende Fakten | Zitierte Quellen | Höchstes Vertrauen |
|---|---|---|---|
| Carbonyl (C=O) | 3 | 3 | 1,0 |
| Methacrylate | 2 | 2 | 1,0 |
| Ketone | 2 | 2 | 1,0 |
| Ester | 2 | 2 | 1,0 |
| Carboxyl (COOH) | 2 | 2 | 1,0 |
| Amide | 2 | 2 | 1,0 |
| Acetate | 2 | 2 | 1,0 |
| N h | 1 | 1 | 1,0 |
Das Ranking spiegelt die gesammelte Literatur Evidenz wider, nicht eine einzelne maßgebliche Regel. Bestätigen Sie immer anhand Ihres Probenkontexts.
Mögliche Materialien
| Material | Unterstützende Peaks | Überlappende Gruppen | Zitierte Quellen |
|---|---|---|---|
| polyimide | 1768, 1720, 1778 | Carbonyl (C=O), Methacrylate | 1 |
Materialien werden nur angezeigt, wenn derselbe Literaturpool diese Bande und mindestens einen weiteren charakteristischen Peak unterstützt.
Spektrumslogik
This band becomes meaningful only when read with its neighboring peaks. In practice, analysts first look at the assignments above, then check whether the same sample also shows other peaks expected for the same structural motif. A lone band near 1768 cm⁻¹ is usually not enough for material identification by itself.
Praktische Anwendung
Diese Art von Abfrage ist üblich bei der Polymeridentifikation, dem Screening unbekannter Kunststoffe, der Fehlersuche in der Qualitätskontrolle, der Verifizierung von Recyclingmaterial und der literaturgestützten Überprüfung der Peakzuordnung.
Häufige Fehler
- Behandlung einer isolierten Bande als Beweis für ein Material, ohne mindestens einen oder zwei unterstützende Peaks zu überprüfen.
- Überlappung ignorieren: Mehrere funktionelle Gruppen können nahe der gleichen Wellenzahl beitragen.
- Überspringen der Validierung, wenn Additive, Mischungen, Oxidation oder Verunreinigungen das Spektrum verfälschen können.
Beratung zur Verifizierung
Wenn weiterhin Mehrdeutigkeit besteht, validieren Sie die Hypothese mit DSC, GC-MS oder TGA, insbesondere bei Mischungen, degradierten Proben und gefüllten Polymeren.
Literatur hinter diesen Zuweisungen
-
Vertrauen 1,0
“ence electrode with a scan rate of 100 mV is attributed to N-H stretching vibration and the cm(cid:2)1 cm(cid:2)1 vibration at around 1768 Under these conditions, the cyclic voltammetry of and 1712 aristhe polyimide shows two pairs of rever”
Chao 等 - 2007 - Electroactive polyimide with oligoaniline in the m DOI: 10.1016/j.eurpolymj.2007.03.048 -
Acetate Vertrauen 1,0
“cm1 cm-1 Peak at 1768 obtained was due to C=O whereas at 1713 the peak corresponded to cm-1 cm-1 benzene ring.”
Bhattacharyya 等 - 2017 - Metallization and APPJ treatment of bismaleimide DOI: 10.1155/2010/987357 -
Acetate Vertrauen 1,0
“The disappearance of the νas(α-C=O) band with the maximum at 1768 cm-1 occurs relatively quickly, while the νs(β-C=O) band intensity at 1758 cm-1 decreases more slowly.”
Tisovsky 等 - 2017 - Effect of Structure on Charge Distribution in the DOI: 10.3390/molecules22111961
Haben Sie ein Spektrum mit dieser Bande?
Laden Sie Ihr FTIR-Spektrum hoch und erhalten Sie in Sekunden einen vollständigen Interpretationsbericht – Peakzuweisungen mit Literaturzitaten, Bibliotheksübereinstimmungen und einer vertrauensbewerteten Evidenzkette.